Component Specific Heat Shield and Insulating Products
*Versa-Shield
Originally designed to protect starters from heat, Versa-Shield can
also be used to protect cool cans, carburetors, fuel pumps and many
more areas of a car, boat, RV or heavy-duty truck. It
has also been found helpful for shielding electrical boxes and
instruments from intense heat. Versa-Shield can easily be cut to
shape, and attaches to itself with hook and loop material.
Versa-Shield will fit most starter assemblies. Simply cut off
excess material with scissors or a sharp knife.
*Turbo Insulation Kit
This turbo kit is designed to fit all turbos from the sport compact
turbos to the large over the road trucks. Designed to reduce turbo
lag and reduce under hood temperatures, the Turbo Insulation Kit
adds additional horsepower while protecting costly components from
unwanted heat. The kit comes complete with all the materials
necessary for a clean, professional looking installation.
*Cell Saver Battery Insulation Kit
DEIs NEW Cell Saver is the Ideal
protection for any automotive battery. Batteries are very
susceptible to heat and vibration that could cause premature
failure and hazardous leaks. Cell Saver is very capable and will
absorb and neutralize any damaging leaky battery acids.
DEIs Cell Savers material is capable of withstanding
radiant temperatures up to 2000 F.
*Hub & Rotor Cover
Design Engineering, Inc. (DEI) has introduced their
Hub and Rotor Cover to protect professional mechanics and backyard
do-it-yourselfers alike from the potential of serious burns.
Working in and around hot brake drums and rotors such as changing
shocks, springs or suspensions can be a painful experience without
some type of protection. Its not just for shielding against harmful
hot spots but can also act as a guard against any sharp edges and
protect against dirt, dust and airborne particles around the track,
shop or backyard garage.
*Aluminized Plug Wire Sheaths
Manufactured of the same material as Heat Sheath. The Plug Wire
Sheath was designed as an inexpensive protection for plug wire
boots or any spot on a plug wire that is close to heat and requires
additional protection. The Aluminized Plug Wire Sheaths can also be
used on lines, wires and hoses that need protection in a specific
area. The Aluminized Plug Wire Sheaths are 6 inches long and 3/4
inches in diameter.
*Dyno Strap Heat Guard
Design Engineering, Inc (DEI) has developed a product
that offers burn-through protection for dyno tie-down straps. Made
of a high-temperature resistant aluminized mylar material, DEIs
Dyno Strap Heat Guard will withstand 500F direct heat and 2000 F of
radiant heat. It measures 5 wide by 3 feet and easily slips over
dyno tie-down ends and slides over strap to be positioned near the
area where exhaust heat exits.
Heat Screen offers an excellent way to reflect radiant heat away
from a vehicle's interior and because of its flexibility, can be
trimmed-to-size to protect against excessive heat sources.
Constructed of a high temperature resistant fiberglass material,
and with a thickness of only .060", Heat Screen features a thermal
barrier on one side made of a superior reflective aluminized mylar
surface capable of withstanding direct heat up to 1200F. Heat
Screen can be used to protect areas where excessive heat can
blister paint, where exhaust pipes run close to the fuel tank, and
has many other applications including floorboards, body panels and
under carpeting. A high temperature adhesive such as DEI's Hi-Temp
Spray Adhesive or Heat Resistant Sealant/Adhesive can be applied to
secure Heat Screen or screws or rivets can be used. DEI's Cool Tape
is ideal for sealing and covering seams.
- 36" x 40" Aluminized Mylar Radiant Matting
- Used in aviation and aerospace industry
- Great protection for painted surfaces
- Multitude of uses around race cars, boats, RV's and trucks
- Aluminized surface reflects up to 2000F radiant /1200F direct
/continuous heat
