Disc Brake Hardware Kit
Wilwood 300-12032 Tubular Bracket Spacer High-Strength Aluminum with Black E-Coat
Wilwood 300-11821 Tubular Bracket Spacer High-Strength Aluminum with Black E-Coat
Wilwood 300-11352 Caliper Bracket Spacer for Internal Disc/Drum Parking Brake
Wilwood 300-13634 Spindle Bracket Bolt Sleeve .506" ID x .563" OD x 1.05" Long
Wilwood 300-12503 Caliper Bridge Spacer for Forged Dynalite, Billet Dynalite & NDL Calipers
Wilwood 300-12434 Rotor Bobbin Anti-Rattle Cap Spring for Aluminum Dynamic Hats
Wilwood 300-12425 Extension Spring for Internal Parking Brake Kits and Brackets
Wilwood 300-3708 Anti-Rattle Spring Clip, Stainless Steel, GP300/GP340 Calipers
EBC FDSK-HARDWEAR2 Replacement Rotor Hardware Kit for 2-Piece Floating Brake Rotors
Wilwood 190-14246 Combo Valve Tubing Long Stainless Steel Brake Line Assembly
Wilwood 230-14217 Hex Head Cap Screw 5/8-18 x 1.50 Grade 8 Silver Caliper Bracket Bolt
Wilwood 230-14413 Dynamic Sprint Rotor Bolt Kit - 6 Hex Head Bolts with T-Nuts
Wilwood 230-15488 Button Head Cap Screw 10-24 x .62 Stainless Steel Brake Bolt
Wilwood 330-14800 Compact Tandem Master Cylinder Replacement Lid Bare Billet Aluminum
What Is a Disc Brake Hardware Kit?
When it comes time to replace brake pads, it's easy to focus entirely on the friction material and overlook the small but critical components that hold everything in place. Disc brake hardware kits supply all the supporting hardware needed for a complete, professional-quality brake job — and skipping them is one of the most common causes of brake noise, uneven pad wear, and premature component failure.
A typical disc brake hardware kit includes anti-rattle clips, abutment clips, caliper guide pins (slide pins), rubber boots, shims, and mounting hardware — the collection of components that keep your brake pads properly seated, your calipers sliding freely, and your rotor contact even and consistent. Over time, these pieces are exposed to heat cycles, road salt, moisture, and debris. Even hardware that looks usable can lose its tension, corrode, or deform enough to cause problems. Replacing brake hardware every time you install new pads restores factory-level caliper movement and pad alignment.
Why Brake Hardware Matters
Problems like brake squeal, clicking noises, dragging pads, and uneven pad wear frequently trace back not to the pads or rotors themselves, but to old or damaged hardware. Anti-rattle clips secure brake pads inside the caliper bracket and prevent excessive movement during braking. Guide pins allow the caliper to float smoothly so that even pressure is applied to both sides of the rotor — when these seize or wear out, one pad wears significantly faster than the other. Shims act as a buffer between the pad backing plate and caliper piston, dampening vibration before it becomes audible squeal. Together, these components are the difference between a brake job that stays quiet and smooth for years and one that has you back in the shop before the season is out.
Choosing the Right Disc Brake Hardware Kit
Hardware kits vary considerably depending on the application. Daily-driver street cars call for OE-replacement hardware focused on quiet, long-lasting operation. Performance builds and racing applications demand hardware engineered to survive extreme heat and repeated hard braking. Disc brake conversion projects on classic vehicles require kits designed specifically around the conversion system being used. Always match the hardware kit to both the vehicle application and the brake components already installed.
Top Brands in Disc Brake Hardware Kits
Wilwood is a globally recognized manufacturer of high-performance disc brake systems, and their hardware selection reflects that engineering pedigree. Wilwood offers a comprehensive range of hardware — including pins, bushings, bolt kits, and parking brake components — purpose-built to complement their performance caliper and rotor systems across street, strip, and race applications.
Right Stuff Detailing has built a strong reputation in the classic car restoration and performance market, specializing in complete disc brake conversion solutions for popular GM, Ford, and Mopar platforms from the 1950s through the 1980s. Their hardware kits are an integral part of bolt-on conversion packages that include all brackets, hardware, lines, and detailed instructions for a correct, no-guesswork installation.
Dorman brings broad OE-coverage to the disc brake hardware category, offering vehicle-specific kits for a wide range of domestic and import applications. Dorman's hardware kits are designed to meet or exceed OEM specifications, making them a reliable choice for everyday service and maintenance across a large variety of makes and models.
Strange Engineering is well known in the drag racing and high-performance community, and their disc brake hardware offerings reflect a focus on durability and strength under demanding conditions. Their hardware solutions are designed to work within serious performance brake setups, making them a go-to for builders who demand race-proven reliability.